產品及技術服務
  1. 首頁
  2. 產品及技術服務
  3. 廢水處理WastewaterTre...
廢水處理 Wastewater Treatment

本公司專利「創新複合式藻菌廢水處理技術」針對不同廢水成分，研發多款專用製劑，有效降低化學需氧量（COD）、氨氮及重金屬含量，同時實現低成本、低污泥、低污染的永續處理目標。

以下為本公司提供之服務及產品：

Our patented “Innovative Composite Algae-Bacteria Wastewater Treatment Technology” develops tailored formulations for different wastewater compositions, effectively reducing chemical oxygen demand (COD), ammonia nitrogen, and heavy metals, while achieving a sustainable solution with low cost, low sludge, and minimal pollution.

services and products provided by our company:

服務流程介紹 Service Process Introduction

廢水評估 Evaluation 廢水取樣試驗 Experiment 建議解決方案 Solution  售後服務 Service
1.電話評估 Telephone
2.現場評估 On-site		 1.採取原廢水樣品 Collect Sample
2.進行試驗 Testing		 1.建議處理方案 Treatment Plan
2.討論與報價 Discussion & Quotation		  提供售後服務 After-sales Service

客製化廢水處理 Customized Wastewater Treatment

流程排序

售前服務

售後服務

一

實驗室分析廢水樣品：為提供最佳的重金屬去除方案，檢測包含COD、BOD、重金屬、SS測試。

現場製劑應用之技術支援，包含定期檢查系統操作情況，提供  相應參數調整建議。

二

技術支援及顧問服務：協助選擇最適合的去除劑及使用方法。

三

1) 製劑測試(客製化製作)。

2) 所需時間：依據廢水的性質和需去除之標的物而異，一般需要3-4天進行杯瓶測試驗證去除效果。

3) 提供測試報告。

四

1) 現場測試(場測)：正式應用於廢水系統前需進行現場測試，至少需一週時間。

2) 測試時間：依測試的複雜程度及客戶需求而調整。

3) 提供測試報告。
五

確認購買後，提供使用教學，確保操作人員正確使用製劑。

Process

Pre-sales Service

After-sales Service

1

Laboratory analysis of wastewater samples: To provide the best heavy metal removal solution, tests include COD, BOD, heavy metals, and SS.

Technical support for
on-site formulation application, including regular inspections of system operation and providing corresponding parameter adjustment recommendations.

2

Technical support and consulting services: Assisting in selecting the most suitable removal agents and usage methods.

3

(1) Formulation testing (customized production).

(2) Required time: Varies depending on the nature of the wastewater and the target substances to be removed; generally, 3-4 days are needed to conduct jar tests to verify removal effectiveness.

(3) Provision of test reports.

4

(1) On-site testing (field testing): Before formal application to the wastewater system, on-site testing is required, lasting at least one week.

(2) Testing duration: Adjusted based on the complexity of the test and customer requirements.

(3) Provision of test reports.
5

After purchase confirmation, provide usage training to ensure operators correctly use the formulation.

創新微生物科技應用於廢水處理 Innovative Microbial Technology applied to Wastewater Treatment

工業廢水處理應用之場域分佈 Distribution of Application Sites for Industrial Wastewater Treatment

  • 以創新複合式微生物技術應用於高COD和含氮廢水處理，可穩定淨化水體，並循環再利用。
  • 以新型態微生物製劑應用於重金屬廢水處理，能達到高效能、低汙泥量的處理效果。
  • 新型態水處理模式，減少廠區廢水產出，並提高水回收再利用性，達到低排放、高環保、降成本的目的。

  • Utilizing innovative composite microbial technology for the treatment of high COD and nitrogen-containing wastewater, achieving stable water purification and enabling recycling and reuse.
  • Applying new-generation microbial formulations in heavy metal wastewater treatment, delivering high efficiency with low sludge production.
  • Introducing a new water treatment model that reduces wastewater generation at the plant, enhances water recovery and reuse, and achieves low emissions, high environmental protection, and cost reduction.

廢水製劑現有規格品及案例 Exiting Specification and Cases of Wastewater Treatment

品項 Item

重金屬去除劑 Metal Adsorbent

目的 Objective

用於處理含有重金屬離子的廢水
Used for treating wastewater containing heavy metal ions.

原理
Principle

通過化學反應將溶解在水中的重金屬轉化為 不溶於水的沉澱物，然後通過沉降或過濾去除這些沉澱物；去除劑能夠顯著降低重金屬的　濃度，通常可達到排放標準要求。
Through chemical reactions, dissolved heavy metals in water are converted into water-insoluble precipitates, which are then removed by sedimentation or filtration. The removal agent can significantly reduce the concentration of heavy metals, typically meeting discharge standard requirements.

產品型號
Model

ZMF-03

ZSMF-02

BMF-06




案例
Case

廢棄物資源回收業 ：

製劑添加量0.1%~0.15%，鋅濃度從80ppm降至0.2ppm以下

Waste recycling industry：

In the waste recycling industry, the agent is added at a dosage of 0.1% to 0.15%, effectively reducing the zinc concentration from 80 ppm to below 0.2 ppm.

化學製品製造業：

製劑添加量0.1%~0.15%， 鉬濃度從80ppm降至11ppm

Chemical manufacturing industry：

In the chemical manufacturing industry, the agent is added at a dosage of 0.1% to 0.15%, effectively reducing the molybdenum concentration from 80 ppm to 11 ppm.

基本金屬製造業：

製劑添加量1%~2%， 硼濃度從805ppm降至169ppm

Basic metal manufacturing industry：

In the basic metal manufacturing industry, the agent is added at a dosage of 1% to 2%, effectively reducing the boron concentration from 805 ppm to 169 ppm.

品項 Item

化學複合式混凝劑 Compound Chemical Preparations

目的 Objective

用於去除懸浮固體和顆粒物，方便後續沉降或過濾。
Used to remove suspended solids and particulates, facilitating subsequent sedimentation or filtration

原理
Principle

—

產品型號
Model

NJ-01

YJC-01

氧化劑 JP-12 （Oxidizing）

案例
Case

食品業、 石化業、電線電纜業：

COD可由55000 ppm降至13000 ppm，移除率達75%，產生汙泥量為4%～8%。

Food Industry，Petrochemical Industry，Wire and Cable Industry：

COD can be reduced from 55,000 ppm to 13,000 ppm, achieving a removal rate of 75%, with sludge production ranging from 4% to 8%.

—

工業廢水、食品業：

COD可由5000～6000 ppm降至2500 ppm，移除率達50%，產生汙泥量為50%～60%

Industrial Wastewater，Food Industry：

COD can be reduced from 5,000–6,000 ppm to 2,500 ppm, achieving a removal rate of 50%, with sludge production ranging from 50% to 60%.

 

回上一頁